-
A 1.Polyurethane has better insulation properties than polystyrene and can easy reach density of 40kg／m³ inside the door blade.
2.Polyurethane foam expand firmly inside the blade,with very strong grip to the sides and to the special aluminum profile of the blade edge,providing very good blade hardness and geometrical stability for better sealing.
3.The door blade can be made in different colors or type of material,such as pre-painted steel sheet,stainless steel,PVC,fiber glass or others.
4.Easy to fit inside the blade reinforcement for hardware that are strong grip by the polyurethane foam,to ensure longer life time of the blade.
5.They have better thermal bridge interruption between internal and external sides to avoid loss of heat to the edges and condensation near the sealing gasket.
6.Round shape gaskets in double density extrusion,hard on fixing part and soft in
sealing part for efficient insulation;and for negative application gaskets are provided with heater easy to replace.
7.There are no rivets or sharp joints on the sides of the blade,to make dirt hard to clean.
8.Most of the hardware are made of PVC with fiber glass or stainless steel with soft shapes and covered screws and nuts,easy to clean and long lasting.
9.All doors,materials used and hardware hold the European Certifications for food proof and work safety regulations.
-
A 1.The experience show that the cold room panels is most wear in the edge of the clear opening,due to accidental crashes and door hardware,that result in significant cold loss;therefore TRT philosophy is to protect this part that is also critical for the gasket tight sealing.
2.The cold room panel is often not strong enough to fix the hardware,such as hinges or sliding system and bear long running wear,whereas the TRT frame is designed to take over all stress of the panel in order to extend the life time of the door and good sealing properties.
3.The PVC frame is desigh also for perfect thermal bridge interruption even when it is cover with stainless steel.
4.For negative application,the heater fixed on the PVC frame,on aluminum special profiles,channel the heat only to defrost the gasket,with minimum loss and only 30w／m heating power.
5.The life time of the PVC frame is longer than the panel and easy to repair or replace any time.
6.The PVC frame can secure the perfect geometrical alignments even when panels are not perfectly mounted,(in line or not vertical),in order to improve the gaskets sealing all around.
7.Due to PVC frame TRT doors are provided with guiding line on the panel,not on the floor,and sliding drop and push system for tight closing.
-
A 1.Better gasket sealing provided by PVC track guiding bends with and without grove and 6 adjusting systems;2 on each wheel support one in the rear guiding system and one in front of the door closing,and always clean floor.
2.Much less wear of the gaskets during operation extend the life time of the door compare with other systems.
3.Easy to open／close even to very large sizes of doors,by eliminating the gasket friction on the panel and extend the hardware／blade life time.
4.Need less power for the automation kit and low energy consumption.
-
A 1.Beside the cooling system,the door is the most were part that can save or loose energy and influence the running cost of the cold rooms;therefore it worth to spend more only once on investment stage and to save money during operation over the life time.By the end the life time cost is lower.
2.They have improved design to overcome the critical problems of cold room doors.Better insulation and strong blades by polyurethane,better and long lasting sealing system,strong frame to protect the panel and easy operation for long life time.
3.Modern design,soft corners,no open rivets／screws／nuts,easy to clean for every operation environment.
-
A 1.The loss of cool and the moisture witch enter through gaps in sealing gaskets and block the cooling unit,can cause up to 30％ of total energy loss of a cold room.Thus by using a better door the energy saving can be 10％-15％,on top of improve operation and life time of the refrigeration plant.
2.Cost of maintenance for the cooling unit and the door,are lower when using better doors.
3.Easy to mount and repair in case of damage with low cost.
-
A 1.In order to save energy and increase the life time of the door.
2.Save energy because the door close automatically at desired time setting and reduce the time when stay open.
3.Increase the life time because the door always is softly operated,correctly closed and protected against accidental crashes,due to safety features of the automation system.
-
A 1.They are quite light and easy to operate in every temperature range,due to special desigh of their hardware.
2.Easy to clean,soft corners and no floor crashes.
3.Work safety operated hardware;locks with safety release European certified.
-
A Hospitals, laboratories, clean rooms, office buildings that need easy clean and tight closing system.
-
A See item 5
-
A They are desigh to last 10 to 15 years in normal operation,without major repairs,but the life time can be 15 to 20 years for an automated one.
